Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAir Duct Cleaning in Studio City, CA
Dryer vent cleaning in Studio City runs $129-$289 depending on access and line length, and most jobs are completed in under two hours. The canyon-mouth geography between Fryman Canyon Road and Ventura Boulevard loads duct systems with a fine ash-and-chaparral particulate that flatland Valley homes rarely see, and the dense 1940s-1960s housing stock means many of those ducts are now 50-70 years old. At CleanRun Air Duct Cleaning, every job starts with a written price, and every vent run gets photographed before and after, so you can see exactly what came out and what the finished work looks like. Call (806) 606-6902 for a free estimate.
Why Studio City Homes Are Different
Studio City sits precisely where Fryman Canyon, Coldwater Canyon, and Laurel Canyon open onto the San Fernando Valley floor. That position acts as a funnel: every brush fire, every Santa Ana wind cycle, and every dry-season dust event in the surrounding mountains channels fine combustion particulate and ash directly into the residential neighborhoods below. After the 2019 Getty Fire, and again after the recurring Mulholland-area burns, technicians working hillside streets above Fryman Canyon Road pulled duct camera footage showing visible ash and fire-retardant residue inside systems that had been cleaned only a few years prior. That residue persists. Flatland cities a few miles north simply do not accumulate this material the same way.
The housing stock compounds the problem. The flatlands hold a dense inventory of post-war ranch homes and bungalows built between the 1940s and 1960s, many still running original or once-retrofitted duct systems. Fifty to seventy years of thermal expansion, remodel patches, and gravity have taken a toll: disconnected joints, compressed flex runs, and debris that has hardened into a surface layer the camera picks up before the vacuum ever goes in. Above Ventura Boulevard, the custom builds and mid-century homes along the hillside streets often have non-standard duct routing added during successive remodels, which complicates cleaning access and makes a documented photo record essential before and after every job.
The Valley heat trap makes it worse. Studio City regularly runs 15-20°F hotter than the Westside, so central HVAC systems here log far more hours than coastal Los Angeles systems. More runtime means more air pulled through the return, more dust deposited inside the plenum and branch runs, and a faster accumulation cycle. Add the seasonal Santa Ana winds pushing fine desert dust through any envelope gap, and Studio City ductwork gets dirty faster than most of Los Angeles. This is not a generic cleaning job. It is a maintenance cycle tied directly to local geography and building age.
Our Main Studio City Services
Two services generate most of the calls from Studio City homeowners, and each has its own dedicated page covering local conditions, pricing, and process in detail.
Air Duct Cleaning in Studio City
Full-system air duct cleaning removes the accumulated dust, pet dander, construction debris, and seasonal ash load from the supply and return side of a home’s ductwork. In Studio City, the work often involves navigating older ranch-home systems with tight attic access and hillside customs with irregular trunk lines. We document every duct run before and after, then leave the customer with a photo record showing exactly what was inside and what the cleaned surface looks like. Full pricing, local conditions, and the process are covered on the Air Duct Cleaning in Studio City page.
HVAC Cleaning in Studio City
HVAC cleaning goes beyond the duct runs to the source components: the blower motor, evaporator coil, drain pan, and plenum. In Studio City, where systems run long hours through Valley summers, coil surfaces accumulate a baked-on film that reduces heat transfer and raises runtime. Removing that film is a documented, photographable result, not a vague improvement claim. The scope, local pricing, and what gets included are all on the HVAC Cleaning in Studio City page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterDryer Vent Cleaning in Studio City
Dryer vent cleaning in Studio City is a fire-prevention service first and an efficiency service second. The 1940s-1960s ranch homes through the flatlands often have long, multi-elbow vent runs that terminate at the roof or snake through crawl spaces, and every bend is a lint trap. Our crews use negative-pressure extraction and rotary brushes sized to the specific vent diameter, and the camera record shows the before, the obstruction, and the after. Most Studio City jobs fall between $129 and $289, depending on line length, access, and the number of elbows. We also install bird guards, reroute poorly designed runs, and document the entire line with the same photo record we use on every job. For the full breakdown of this service across the broader area, see Dryer Vent Cleaning.
Dryer Vent Inspection
Signs you need it
Clothes take more than one full cycle to dry, the dryer exterior runs hot to the touch, or a faint burning smell appears mid-cycle.
What it costs in Studio City
A visual inspection with a camera scope of the full vent line runs $49-$99, and the report includes still photos of any obstruction, gap, or disconnected section.
How we do it
We scope the full run from the dryer connection to the exterior termination, photograph any restriction or damage, and write the findings into a documented report with a flat price for whatever correction is needed.
Lint Removal
Signs you need it
Visible lint accumulation around the dryer, reduced airflow at the exterior vent cap, or a history of the vent not being cleaned in the last two years.
What it costs in Studio City
Full lint removal through the entire vent line runs $129-$229 in Studio City, depending on run length and the number of elbows in the line.
How we do it
We connect a professional-grade negative-pressure extraction system to the vent, feed a rotary brush through every bend and straight section, and photograph the interior before and after removal.
Bird Guard Installation
Signs you need it
Nesting material visible at the exterior vent cap, bird activity around the termination point, or repeated clogging from organic debris that lint removal cannot explain.
What it costs in Studio City
A galvanized or stainless bird guard installed over the exterior vent termination runs $89-$149, including the guard itself and verification with the camera that airflow remains unobstructed.
How we do it
We clear the line, mount a corrosion-resistant guard over the termination, and photograph the installed guard from both the exterior and interior view of the line.
What Dryer Vent Cleaning Costs in Studio City
| Item | Typical range in Studio City |
|---|---|
| Dryer vent inspection with camera scope | $49-$99 |
| Full lint removal, standard single-story run | $129-$229 |
| Bird guard installation with inspection | $89-$149 |
How often does a dryer vent need cleaning in Studio City?
Every 12 to 24 months for a household of two or more. Longer runs with multiple elbows, common in older Studio City ranches, should be inspected annually because each bend adds a collection point. Call (806) 606-6902 for a documented assessment.
Why does my Studio City dryer vent clog faster than my old house?
Older homes here often route dryer vents through crawl spaces or up to the roof, adding length and elbows. Each bend catches lint, and Valley heat bakes the buildup into a harder, denser obstruction that restricts airflow faster.
Duct Repair & Sealing in Studio City
Duct repair and sealing in Studio City is about restoring the pressure envelope of a system that is often 50 to 70 years old. The same post-war duct networks that accumulate debris also leak: disconnected joints in crawl spaces, compressed flex runs in remodels, and return trunks pulling attic air through unsealed gaps. In the hillside customs above Ventura Boulevard, we regularly find duct sections that were rerouted during renovations and never sealed properly, pulling hot attic air into the conditioned airstream all summer. We locate these leaks with a pressure diagnostic, seal them with mastic or replace the damaged section, and photograph every repair. For the complete service scope across the region, see Duct Repair & Sealing.
Duct Sealing
Signs you need it
Rooms that never reach the thermostat setting, visible dust collecting around registers between cleanings, or a utility bill that climbs every July.
What it costs in Studio City
Sealing accessible duct joints and seams with mastic runs $295-$595 for a typical single-system home, based on the number of runs and access points.
How we do it
We identify leak points with a pressure test and smoke pencil, brush or trowel mastic sealant onto each separated joint, and photograph the sealed seams before and after.
Flex Duct Repair
Signs you need it
A sagging or kinked flex run visible in the attic, rooms at the end of a run with noticeably weak airflow, or a tear discovered during cleaning that is pulling unfiltered air into the system.
What it costs in Studio City
Replacing a torn or collapsed flex duct section runs $195-$395 per run in Studio City, including the new insulated flex, connectors, and sealing.
How we do it
We cut out the damaged or compressed section, install new insulated flex with proper support straps, seal both ends with mastic, and photograph the finished run before and after airflow verification.
Mastic Sealant
Signs you need it
Duct tape residue visible on seams, which deteriorates and falls off within a few seasons, leaving the joint open.
What it costs in Studio City
Applying mastic sealant to existing tape seams and open joints runs $45-$120 per accessible joint, priced after a camera inspection of the affected runs.
How we do it
We remove failed tape, brush mastic deeply into each seam and joint with a full-coverage technique, and document the cured seal with photos once the job is done.
What Duct Repair & Sealing Costs in Studio City
| Item | Typical range in Studio City |
|---|---|
| Duct sealing (accessible joints, per home) | $295-$595 |
| Flex duct replacement (per run) | $195-$395 |
| Mastic sealant (per accessible joint) | $45-$120 |
What causes duct leaks in older Studio City homes?
Sheet metal ducts from the 1950s and 1960s were assembled with mechanical fasteners and thin tape that degrades over decades. Thermal expansion from long Valley cooling seasons works the joints open, and remodel patches often leave flex runs unsupported or unsealed.
How do I know if my ducts need sealing or just cleaning?
A pressure diagnostic answers it. Cleaning removes debris from the inside surfaces; sealing closes the gaps where air leaves the system entirely. In Studio City, homes over 40 years old typically need both, which is why we camera-inspect before recommending either.
Air Quality & Sanitizing in Studio City
Air quality and sanitizing in Studio City addresses the material that remains after debris is removed: the microbial growth, odor, and fine ash residue that clings to interior duct surfaces after decades of exposure to canyon-wind particulate. Wildfire smoke from the Getty Fire and recurring Mulholland-area burns leaves a film that a vacuum alone does not remove. Homes in the older flatlands, where crawl spaces and attics run humid in the winter months, are especially prone to mold colonization inside the ductwork. We photograph the affected surfaces, apply the appropriate sanitizing agent, and document everything. For the full scope of this service and the products used, see Air Quality & Sanitizing.
Mold Treatment
Signs you need it
Visible mold growth on interior duct surfaces, persistent musty odor that returns after cleaning, or a mold inspection that flagged the system as a source.
What it costs in Studio City
Full mold treatment of accessible duct surfaces runs $595-$995 for an average single-system home, depending on affected surface area and the number of runs.
How we do it
We apply an EPA-registered antimicrobial to the affected surfaces using professional-grade fogging equipment, photograph the treated areas, and provide a written record of the product and coverage.
Odor Removal
Signs you need it
Smoke odor from wildfire events that persists months after the fire, pet odor that returns whenever the system runs, or a stale cooking odor that has layered into the duct interior.
What it costs in Studio City
Duct odor removal with a full-system fogging application runs $295-$495 in Studio City, including the sanitizing agent and before-and-after photo record.
How we do it
We run a full cleaning pass first to remove the odor-carrying particulate, then fog the entire system with a professional-grade deodorizing agent and photograph the treated surfaces.
UV Light Installation
Signs you need it
Recurring mold growth despite treatment, a medical need for reduced microbial load in the airstream, or a system that sits dark and humid for long stretches.
What it costs in Studio City
A UV-C light installed at the evaporator coil or supply plenum runs $695-$1,195 per unit, depending on the system configuration and the specific lamp model.
How we do it
We mount the UV-C lamp in the plenum or at the coil, run dedicated wiring from a protected circuit, verify operation with a radiometer reading, and document the installation with photos.
What Air Quality & Sanitizing Costs in Studio City
| Item | Typical range in Studio City |
|---|---|
| Mold treatment (accessible duct surfaces) | $595-$995 |
| Odor removal with full-system fogging | $295-$495 |
| UV light installation (per unit) | $695-$1,195 |
Can sanitizing actually remove wildfire smoke odor from ducts?
Most of the smoke odor lives in the fine ash particulate that coats duct surfaces, so the first step is removal, not masking. Fogging then treats residual odor on the cleaned surfaces. Studio City homes near the canyon mouths often need both passes.
Is the sanitizing solution safe for my family and pets?
The products we use are EPA-registered for use in occupied spaces and are applied to interior duct surfaces, not living spaces. We document the product name and application coverage in writing on every job, so you know exactly what was used.
Brands We Service in Studio City
Our Studio City crews work on systems built around Honeywell, Aprilaire, and Rotobrush components, along with Nikro and Abatement Technologies equipment in the truck. Common filters, gaskets, and UV replacement lamps are stocked on the truck for same-visit swaps. For the full list, see our brands.
Pricing for Air Duct Cleaning in Studio City, CA
| Service | Typical range in Studio City |
|---|---|
| Dryer vent inspection with camera scope | $49-$99 |
| Full lint removal (single-story run) | $129-$229 |
| Bird guard installation | $89-$149 |
| Duct sealing (accessible joints, per home) | $295-$595 |
| Flex duct replacement (per run) | $195-$395 |
| Mastic sealant (per accessible joint) | $45-$120 |
| Mold treatment (accessible duct surfaces) | $595-$995 |
| Odor removal with full-system fogging | $295-$495 |
| UV light installation (per unit) | $695-$1,195 |
What pushes a Studio City quote toward the top of a range is access: hillside homes with attic trunk lines that require staging, crawl-space runs under post-war floor framing, and vent lines with multiple elbows all add labor time. The range also moves with the number of runs to be sealed or treated. Whatever the final number is, it is written before any panel comes off, and it does not change after work begins. That is Haven Standard Clause 1.
Neighborhoods We Serve in Studio City
We work throughout Studio City, from the flatlands south of Ventura Boulevard up through the hillside streets above Fryman Canyon Road and Laurel Canyon Boulevard. Crews are dispatched from the brand’s Los Angeles office and typically reach Studio City destinations within the same scheduling window.
- Colfax Meadows
- Fryman Canyon area
- Silver Triangle
- Ventura Boulevard corridor
- Carpenter Square area
Service Area - Cities Near Studio City
CleanRun Air Duct Cleaning serves Studio City and the surrounding communities. Homeowners in North Hollywood, CA, Universal City, CA, Van Nuys, CA, and West Hollywood, CA can schedule the same written-price, documented-photo-record service on the same scheduling window.
Serving Studio City, CA - Our Local Coverage Area
We’re based in the Studio City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Air Duct Cleaning in Studio City
Most Studio City jobs are scheduled within the same week the call is placed, often sooner. Scheduling is coordinated from the Los Angeles office, and the crew arrives with a written price before any work starts. Call (806) 606-6902 to check current availability.
Most single-family homes in Studio City do not require HOA approval for interior duct or vent work. Hillside communities with shared walls or centralized systems may have restrictions, so we recommend checking your governing documents before scheduling. The work itself is non-invasive and requires no exterior modifications in most cases.
Every CleanRun job includes a documented photo record of every duct run and vent line, taken before and after the work. The written scope and the 365-Day Done Right Promise are also provided in writing, so the record is complete and reviewable at any point.
For a free estimate on any duct or vent service in Studio City, call CleanRun Air Duct Cleaning at (806) 606-6902. Written price before any work starts, every time.
What happens when you call
- 1A real person answersNo phone trees - talk to a local air duct cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Studio City Customers Say
"The before and after photographs of each run are the reason I used them. You cannot argue with what came out of the return."
- Marguerite O."Flat price agreed up front, no per-vent add-ons at the end. That was the whole reason I did not call the coupon company."
- Suzanne B."The dryer vent was almost completely blocked with lint. They showed me the photograph and I understood immediately why the dryer had been running twice."
- Lucia M.