Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Duct Repair & Sealing in New York City: What to Know First
Abatement Technologies duct repair and sealing in New York City typically runs $350 to $1,100 per job, depending on whether we’re sealing a few leaking joints with mastic or replacing sections of damaged flex duct in a Manhattan high-rise chase. We’re an independent Abatement Technologies service provider, not a factory-authorized shop, and we work on the brand’s portable HEPA units and the duct runs connected to them in apartments, co-ops, and townhouses across all five boroughs. Most repair jobs are completed in one visit, with a written price in your hand before any panel comes off. If you own an Abatement Technologies negative air machine or ducted HEPA setup and the airflow is weak, the registers are whistling, or the foil tape at the seams is letting go, this page is for you. Call (806) 606-6902 and we’ll schedule the call.
Key Takeaways
- We repair and seal the duct runs connected to Abatement Technologies HEPA units, not the units’ internal filters or motors.
- Written price before work starts, every job, no exceptions. That’s Haven Standard Clause 1.
- You get a photo record of every duct run, before and after, as a standard deliverable.
- 365-Day Done Right Promise in writing. If the seal doesn’t hold or the airflow is still wrong, we make it right.
How Abatement Technologies Products Fail - and How We Fix Them
Abatement Technologies builds serious filtration hardware, but the duct runs attached to those units take a beating in New York City buildings. Here’s what we actually find when the camera goes in.
- Foil tape failure at HEPA unit collars. On the Predator and AirDyne series, the factory connection between the duct collar and the first run of flex relies on adhesive foil tape. In a New York City mechanical closet that cycles between 55°F in January and 95°F in August, that adhesive dries out and lets go. We pull the old tape, clean the collar with a solvent that won’t attack the plastic, and reseal with mastic plus a mechanical draw band. Tape alone just fails again in two seasons.
- Flex duct compression behind drywall. We see this most on the HEPA-AIRE portable units that get routed through soffits and chases in prewar co-ops. The inner liner of the flex collapses where the duct makes a tight turn, which drops static pressure and cuts airflow by half or more. We cut inspection access, replace the crushed section with rigid metal elbows at the turns, and reconnect with properly torqued draw bands, not zip ties.
- Leakage at ductboard plenum seams. Some Abatement Technologies installations use ductboard plenums in the ceiling. The foil facing splits at the seams after a decade or two, and the fiberglass underneath degrades from New York City’s humidity swings. The fix is either a full mastic-and-mesh reinforcement on the seams or, if the board is too far gone, replacement with fabricated metal. We’ll show you the photo before we recommend which way to go.
- Vibration wear where duct meets the unit deck. HEPA units run constantly on remediation and renovation jobs, and that constant vibration frets the duct connection at the deck. The symptom is a high-pitched whistle at the seam and dust streaks on the outside of the duct. We isolate the connection with a flexible canvas connector, which absorbs the vibration before it can peel the seal again.
- Improperly sized returns on the AirDyne 2500. We’ve opened up enough of these to know the factory return plenum is often undersized for the building’s actual duct run. That restriction causes the unit to pull harder, which pulls the flex duct oval and pops seams open over time. We reseal the runs and, where feasible, upsize the return collar with an adapter plate so the system isn’t fighting itself. The photo record shows the before and after so you can see the difference between a patch and a proper fix.
BeforeAfterOur Abatement Technologies Duct Repair & Sealing Process
- 1
Call and written scope request. You call (806) 606-6902. We ask for the model number on the unit’s data plate and send a technician out. No quote over the phone based on guesses.
- 2
Camera inspection. We run a camera through every accessible duct run. We’re looking for collapsed flex, failed tape, loose draw bands, and leaks at the plenum. You see the footage. We don’t ask you to take our word for anything.
- 3
Written price before work starts. Haven Standard Clause 1. One number for the whole repair, broken down by line item. You approve it in writing, and that number doesn’t move.
- 4
Parts decision, in writing. If the repair calls for replacement flex or collars, we tell you whether OEM Abatement Technologies parts make sense for your situation or whether a quality aftermarket equivalent does the same job for less. The trade-offs go in writing too, so there’s no ambiguity about what went in.
- 5
The repair and sealing. We cut out the failed section, install the new run or rework the seams, and seal with mastic and mechanical connections. No tape-only repairs. We don’t do tape-only repairs because tape is what failed in the first place.
- 6
Test, document, done. We run the system, measure the airflow before and after at the register, and photograph every run we touched. You get the complete photo record, the written scope, and the 365-Day Done Right Promise in writing before we leave.
What Abatement Technologies Duct Repair & Sealing Costs in New York City
Here are the ranges we write on the estimate for the most common Abatement Technologies jobs in New York City. These are whole-system numbers, not teaser rates that grow once the van is parked outside.
| Job | Typical Range (New York City) |
|---|---|
| Reseal foil tape failures at one HEPA unit collar | $220 - $420 |
| Replace one collapsed flex duct run (up to 15 ft) | $340 - $760 |
| Mastic-and-mesh reinforcement on ductboard plenum seams | $400 - $850 |
| Vibration isolation connector at unit deck | $280 - $520 |
| Full duct run replacement on an AirDyne or Predator setup | $700 - $1,600 |
What moves the price: access. A duct run you can reach from a drop ceiling costs less than the same run behind a New York City plaster wall that requires cutting a new access panel. Length of the failed run matters too. And whether the existing collar needs an adapter plate or not. We put the exact number in writing before anything gets touched. Call (806) 606-6902 for a free estimate, and we’ll come out and put the camera in.
Why New York City Homeowners Call CleanRun Air Duct Cleaning for Abatement Technologies Work
We started this company in 2013 and we’ve documented every duct run we’ve touched since day one. The photo tells you what’s in there. Everything else is just paperwork. That’s the whole approach, and it’s why homeowners in New York City who own Abatement Technologies equipment call us instead of the shop-vac special. Our technicians are background-checked and uniformed under Haven Standard Clause 3, and they carry professional-grade equipment from Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, and Guardsman, so the tooling matches the job. If you’ve got a Lennox, Trane, or Carrier system on a different floor, we service those too, same written-price policy. And everything we do is backed by the 365-Day Done Right Promise, in writing, not as a marketing line. Tomas Reyes runs the crews and still puts his name on the scope sheet. That’s accountability you can hold in your hand.
FAQs
No. As an independent Abatement Technologies service provider, we perform repairs and sealing on the duct runs connected to the units, which are outside the manufacturer’s internal component warranty. Our work doesn’t touch the filter housing, motor, or controls, so the OEM warranty on the unit itself stays intact. We document the scope in writing before work starts, so if a future warranty claim ever comes up, you have a record of exactly what was done and what was not touched.
Both are available, and we’ll tell you which one makes sense for your specific repair. OEM flex duct, collars, and draw bands are available through New York City HVAC supply houses without long lead times. But for certain components, a quality aftermarket equivalent performs identically and costs meaningfully less. We put the trade-off in writing on the estimate and let you decide. Either way, the price is fixed before work starts. Call (806) 606-6902 and we’ll walk you through it.
Most repairs to the duct runs we’ve described are completed in a single visit, typically within two to four hours, as long as the access is not walled off. We schedule based on technician availability, not fictitious urgency. We won’t tell you it’s an emergency if it isn’t. If you need a written estimate first, we come out, put the camera in, and give you the number. No pressure, no countdown timers.
You’ll have photographic evidence. Every CleanRun job concludes with a Documented Photo Record of every duct run we touched, with before and after shots from inside the run where the camera reached. You’ll see the failed seam and then you’ll see the mastic-sealed joint. If that isn’t enough, the 365-Day Done Right Promise says in writing that if the work isn’t right, we make it right. Not subject to manager approval, not a policy that expires when the truck leaves your building.
That depends on what the camera shows. If the flex liner is intact and the failures are at the seams and collars, sealing and reinforcement at $220 to $850 is almost always the right call. If the inner liner has collapsed or the ductboard plenum is shedding fiberglass into the airstream, replacement is the honest fix. We’ll show you the footage and quote both options in writing when both are viable. You make the call with the evidence in front of you. Call (806) 606-6902 for a free estimate.
If you own an Abatement Technologies unit in New York City and the airflow is weak, the seams are leaking, or you’ve inherited ductwork that hasn’t been touched since before Bloomberg, call (806) 606-6902. We’ll send a technician, run the camera, and put the written price in your hand before a single panel comes off. No bait pricing, no call-for-a-quote games, no work without your written approval. That’s how we’ve done it since 2013, and that’s how we’ll do it on your job.
Written by Tomas Reyes, Owner & Lead Technician, CleanRun Air Duct Cleaning at CleanRun Air Duct Cleaning, serving New York City and nearby areas.