Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAir Duct Cleaning in Spokane, WA
Dryer vent cleaning in Spokane handles a specific local problem: wildfire smoke particulate from August and September loading into dryer exhaust runs, then cold-season use packing that residue with lint from October through March. Spokane’s mix of pre-1960 craftsman homes in Browne’s Addition and South Hill, plus 1950s-1970s tract housing across the Spokane Valley, means dryer vents run through basements, crawlspaces, and exterior walls with irregular paths that trap more lint than modern straight-run designs. Call (806) 606-6902 for a written quote before any work starts.
Why Spokane Homes Are Different
Spokane sits in the inland Northwest’s wildfire smoke corridor. August and September bring hazardous AQI readings as smoke from fires across eastern Washington, Idaho, and Montana settles over the city. Residents seal their homes and run forced-air systems continuously to filter that smoke, driving fine ash particulate (PM2.5) deep into ductwork. Then winter arrives. Spokane averages over 40 inches of snowfall and extended subfreezing stretches, so gas forced-air furnaces run heavily from October through March, far more continuous run-time than in milder Pacific Northwest cities. That back-to-back seasonal punishment, smoke loading followed by high-volume furnace operation, produces duct contamination genuinely different in character and quantity from anything in western Washington cities shielded by the Cascades.
The housing stock compounds it. Browne’s Addition and South Hill hold craftsman-era bungalows and foursquares originally heated by gravity furnaces, later retrofitted with forced-air systems. The result is irregular duct runs, mismatched flex-duct additions, and poorly sealed plenums that accumulate debris and resist clean access. Post-WWII tract development across the Spokane Valley and North Side added 1950s-1970s homes with aging galvanized and sheet-metal ductwork now corroding under Spokane’s moderately hard water. Technicians working South Hill and Spokane Valley homes after bad fire years, 2020, 2021, and 2023 were severe, routinely pull registers and find a visible fine gray ash film coating interior duct walls.
Our Main Spokane Services
Spokane homeowners call most about full-system air duct cleaning and HVAC cleaning, both driven by the same wildfire-smoke-and-cold-winter cycle that loads particulate into forced-air systems faster than national averages would predict.
Air Duct Cleaning in Spokane
Full-system Air Duct Cleaning in Spokane removes the fine gray ash film, construction debris, and household dust that builds up in supply and return plenums, duct runs, and registers. In pre-1960 homes with gravity-furnace conversions, the irregular duct paths make negative-pressure extraction the correct method, not a shop-vac pass. Every job ends with a documented photo record of the inside of every run, before and after, delivered as part of the standard scope.
HVAC Cleaning in Spokane
HVAC Cleaning in Spokane covers the air handler, evaporator coil, blower wheel, and condensate pan, the components that take the most punishment during smoke season when systems run on recirculate for days. Spokane’s hard water accelerates scale on coils and pans. The job uses professional-grade equipment from Rotobrush and Nikro, and the blower wheel assembly is photographed before and after just like the duct runs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterDryer Vent Cleaning in Spokane
Dryer vent cleaning in Spokane removes the compacted lint and wildfire ash residue that builds up in dryer exhaust runs from the dryer connection to the exterior termination point. The local problem is specific: smoke-season particulate gets pulled into the dryer’s exhaust stream when the dryer runs during August and September, then cold-season use from October through March bakes that fine ash into a hardened lint matrix. In older South Hill and Browne’s Addition homes, where dryer vents often run through long basement paths or up through exterior walls, that buildup creates a genuine fire risk and forces the dryer to work harder than it should. Our full Dryer Vent Cleaning scope covers inspection, cleaning, and the documentation every Spokane homeowner should expect.
Dryer Vent Inspection
Signs you need it
Clothes take longer than 45 minutes to dry, the dryer exterior gets hot to the touch, or you notice a burning smell when the dryer runs.
What it costs in Spokane
Dryer vent inspection in Spokane typically ranges from $89 to $189 depending on run length and access.
How we do it
We feed a camera through the full run from dryer connection to exterior termination, photograph the blockage points, and measure airflow with an anemometer before and after.
Vent Cleaning
Signs you need it
Visible lint at the exterior vent hood, a flap that does not fully open during operation, or more than a year since the last cleaning.
What it costs in Spokane
Dryer vent cleaning in Spokane typically runs $150 to $300 for the full run, with the price set in writing before the crew starts.
How we do it
We use a HEPA-filtered negative-pressure machine with rotating brush attachments to break the ash-and-lint matrix loose and pull it back into a sealed collection container, never blowing it into the room.
Bird Guard Installation
Signs you need it
Birds nesting at the exterior vent termination, twigs or nesting material visible in the vent hood, or chirping sounds near the dryer wall.
What it costs in Spokane
Bird guard installation in Spokane typically runs $85 to $160 including the guard hardware, depending on termination height and accessibility.
How we do it
We mount a galvanized or stainless guard over the exterior termination, photograph the finished work, and confirm airflow remains within manufacturer spec.
What Dryer Vent Cleaning Costs in Spokane
| Item | Typical range in Spokane |
|---|---|
| Dryer vent inspection | $89 - $189 |
| Dryer vent cleaning | $150 - $300 |
| Bird guard installation | $85 - $160 |
Why are some Spokane dryer vent quotes so much lower?
Low quotes often cover only the first few feet of run accessible from the dryer, leaving the wall and roof sections untouched. Our written price covers the full run, every time, with photos proving it.
How do I know the vent was actually cleaned?
You receive a documented photo record of the inside of the full run, before and after, delivered with your written scope. The camera does not lie about what was in there.
Duct Repair & Sealing in Spokane
Duct repair and sealing in Spokane fixes the leaks, gaps, and failed flex connections that waste conditioned air in homes already running furnaces harder than almost anywhere else in the Pacific Northwest. Pre-1960 gravity-furnace conversions on the South Hill and in Browne’s Addition typically have mastic joints that dried out decades ago, while 1950s-1970s tract homes across the Spokane Valley and North Side show corroded sheet-metal seams and collapsed flex runs. Leaks mean heated air ends up in crawlspaces and attics, not rooms. Our Duct Repair & Sealing scope addresses the full system, from plenum to register.
Duct Sealing
Signs you need it
Rooms that never reach set temperature, dust accumulating quickly after cleaning, or utility bills that spike in January and February.
What it costs in Spokane
Duct sealing in Spokane typically ranges from $400 to $1,100 depending on accessible linear footage and the number of joints needing work.
How we do it
We locate leaks with a pressure test or visual inspection, then seal joints and seams with fiber-reinforced mastic applied to code, photographing each repaired section before and after.
Flex Duct Repair
Signs you need it
Crushed, kinked, or disconnected flex runs visible in the attic or crawlspace, often found during a routine inspection after home renovations.
What it costs in Spokane
Flex duct repair in Spokane typically ranges from $200 to $450 per run, depending on diameter, length, and access difficulty.
How we do it
We remove the failed flex section, install new R-6 or R-8 insulated flex duct to match the system, and seal both terminations with mastic under Haven Standard Clause 1: written price before any work starts.
What Duct Repair & Sealing Costs in Spokane
| Item | Typical range in Spokane |
|---|---|
| Duct sealing | $400 - $1,100 |
| Flex duct repair | $200 - $450 per run |
| Supply plenum replacement | $350 - $850 |
Will duct sealing actually reduce my heating bill in Spokane?
Sealed ducts reduce the volume of heated air lost to unconditioned spaces, which matters more in Spokane where furnaces run continuously for months. The exact savings depend on how much leakage existed before, which our pressure test quantifies.
Is duct tape a permanent fix?
No, and most building codes prohibit it. We use fiber-reinforced mastic and UL-rated tapes designed for HVAC systems, and we photograph every repair so you see the difference between a patch and a proper seal.
Air Quality & Sanitizing in Spokane
Air quality and sanitizing in Spokane addresses what smoke season and a closed-up winter leave behind: fine particulate, microbial growth, and odors embedded in the duct system and air handler. Spokane’s August-September smoke events force residents to run systems on recirculate for days, overwhelming standard 1-inch filters and depositing combustion byproducts directly into air distribution. Then winter’s continuous furnace operation keeps those particles airborne and recirculating. Homes with pre-1960 duct retrofits in Browne’s Addition and South Hill often show visible gray ash film inside supply runs. Our Air Quality & Sanitizing scope includes treatment, documentation, and equipment installation.
Mold Treatment
Signs you need it
Musty smell from registers when the fan runs, visible microbial growth on duct interiors found during inspection, or a known moisture event in the crawlspace or attic.
What it costs in Spokane
Mold treatment in Spokane typically ranges from $350 to $900 depending on affected surface area and whether the air handler requires treatment.
How we do it
We apply an EPA-registered antimicrobial to affected surfaces using professional application equipment from Abatement Technologies, then photograph treated areas and provide a written treatment record.
Odor Removal
Signs you need it
Persistent smoke, pet, cooking, or musty odors that return after standard cleaning, often concentrated in specific rooms or when the system first cycles on.
What it costs in Spokane
Odor removal in Spokane typically ranges from $250 to $600 depending on the source and whether coil or blower cleaning is also required.
How we do it
We clean the accessible duct surfaces, treat porous materials with an odor-neutralizing agent, and install activated-carbon or photocatalytic filtration if the source persists.
What Air Quality & Sanitizing Costs in Spokane
| Item | Typical range in Spokane |
|---|---|
| Mold treatment | $350 - $900 |
| Odor removal | $250 - $600 |
| UV light installation | $450 - $950 |
Does wildfire smoke actually stay in my ducts permanently?
The fine ash particulate settles inside duct runs and gets redistributed every time the fan cycles. Standard cleaning removes it, but the residue can return if the system runs again during the next smoke event without upgraded filtration.
Will sanitizing fix my allergies in Spokane?
Allergies respond to particulate reduction, not promises. Our process removes the physical load, documents the before and after with photography, and leaves you with a written record of what was actually found and treated.
Brands We Service in Spokane
We service all major HVAC brands in Spokane, with parts and compatible components stocked locally for faster turnaround. Our equipment roster includes professional-grade tools from Rotobrush, Nikro, and Abatement Technologies. See our brands for the full compatibility list.
Pricing for Air Duct Cleaning in Spokane, WA
| Service | Typical range in Spokane |
|---|---|
| Dryer vent inspection | $89 - $189 |
| Dryer vent cleaning | $150 - $300 |
| Bird guard installation | $85 - $160 |
| Duct sealing | $400 - $1,100 |
| Flex duct repair | $200 - $450 per run |
| Supply plenum replacement | $350 - $850 |
| Mold treatment | $350 - $900 |
| Odor removal | $250 - $600 |
| UV light installation | $450 - $950 |
Spokane’s older housing stock pushes prices toward the upper end of these ranges when irregular duct paths and long crawlspace runs make access slower. Every written price is delivered before any work starts, under Haven Standard Clause 1, with no per-vent pricing and no surprise line items.
Neighborhoods We Serve in Spokane
We work throughout Spokane, from the craftsman-era homes of Browne’s Addition to the mid-century tract housing of the Spokane Valley. Response time is typically same-week for scheduled work, with inspection appointments often available within a few days of a call.
- Browne’s Addition
- South Hill
- Spokane Valley
- North Side
- Perry District
Service Area - Cities Near Spokane
Our Spokane crews also serve nearby communities across the inland Northwest. We work in Redmond, WA, Kirkland, WA, Bellevue, WA, and Everett, MA for select residential projects and specialized air quality work.
Serving Spokane, WA - Our Local Coverage Area
We’re based in the Spokane area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Air Duct Cleaning in Spokane
Most Spokane appointments are scheduled within the same week, often within a few days. Inspection visits are typically available faster. We do not offer same-day service or 24/7 dispatch because the work is scheduled, documented, and priced in writing before the crew arrives. Call (806) 606-6902 to check current availability.
Duct cleaning, sanitizing, and most sealing work does not require a city permit in Spokane. Structural modifications or new duct installation may trigger building code review, which we identify during the written estimate process. We handle the scope you need and flag anything requiring city approval before work begins.
Yes, those systems present specific challenges: irregular duct runs, mismatched flex additions, and poorly sealed plenums. We photograph every run before and after, which matters more in pre-1960 homes where access is harder and documentation proves what was actually cleaned or sealed. Our written price covers the full system, not just the accessible sections.
Call (806) 606-6902 for a free estimate with a written price before any work starts. Every Spokane job includes a documented photo record of every duct run, before and after, delivered as part of the standard scope.
What happens when you call
- 1A real person answersNo phone trees - talk to a local air duct cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Spokane Customers Say
"The before and after photographs of each run are the reason I used them. You cannot argue with what came out of the return."
- Marguerite O."Flat price agreed up front, no per-vent add-ons at the end. That was the whole reason I did not call the coupon company."
- Suzanne B."The dryer vent was almost completely blocked with lint. They showed me the photograph and I understood immediately why the dryer had been running twice."
- Lucia M.