Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAir Duct Cleaning in Temple City, CA
Dryer vent cleaning is the single most-requested service we handle in Temple City, and the reason is written into the housing stock: post-WWII ranch homes built before 1970 with original dryer exhaust runs that were never designed to move the volume of lint a modern high-efficiency dryer produces. Add 10-15°F hotter inland summer afternoons and the fine particulate load from the San Gabriel Mountain airshed, and Temple City ducts and vents foul faster than nearly anywhere else in the LA basin. If you need a written price before any work starts, call (806) 606-6902.
Why Temple City Homes Are Different
Temple City sits directly against the base of the San Gabriel Mountains, and that geography drives everything we see in the field. Smog and fine PM2.5 particulate accumulate against the mountain range at measurably higher concentrations than coastal or mid-basin communities, so duct interiors here load with a finer, stickier contaminant layer. The river rock and stucco ranch homes that define neighborhoods south of Las Tunas Drive and north of Live Oak Avenue were largely built between the late 1940s and late 1960s, and many still carry their original fiberglass duct board or early flex-duct runs. Attic temperatures above 140°F in summer bake these materials year after year, and the dry Santa Ana wind cycles push desert dust through every seam and joint that thermal cycling has already begun to separate.
What our technicians find on nearly every Temple City job is a specific failure pattern: flex-duct connectors on 1960s-era systems that have turned brittle and partially collapsed at the elbows, creating turbulence zones where debris collects in thick deposits. This is not a generic “dirty ducts” situation. It is a structural problem in the leak path that means any cleaning done without a sealing step is incomplete. When we run a Rotobrush negative-pressure extraction through these older runs, the before photo typically shows exactly where the connector has failed.
Our Main Temple City Services
Most Temple City homeowners reach out for one of two reasons: full duct cleaning to remove years of accumulated particulate, or a deeper HVAC cleaning that addresses the blower, evaporator coil, and return plenum. Both are documented with before-and-after photos of every duct run.
Air Duct Cleaning in Temple City
Air duct cleaning in a 1950s Temple City ranch means contending with dust, pet dander, and wildfire residue that has settled into every run, plus fiberglass particles from degrading duct board. We photograph the inside of each duct before and after negative-pressure extraction, so the record shows exactly what came out. Read the full scope on our dedicated Air Duct Cleaning in Temple City page, including pricing for this market.
HVAC Cleaning in Temple City
HVAC cleaning here focuses on the components Temple City’s inland heat punishes hardest: evaporator coils, blower wheels, and return plenums on retrofitted systems that were originally heating-only. A coil clogged with fine SGV particulate forces the compressor to run longer and hotter. The complete breakdown of what this service includes is on the HVAC Cleaning in Temple City page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterDryer Vent Cleaning in Temple City
Dryer vent cleaning in Temple City runs into two local realities on nearly every job. First, the original vent runs in those 1940s-1960s ranch homes are typically uninsulated galvanized pipe in a 140°F attic, with long horizontal stretches that collect lint at every joint. Second, the fine desert dust that Santa Ana winds force into the home interior also gets pulled through the dryer drum and into the vent, mixing with lint into a compacted layer that hardens in the heat. Call (806) 606-6902 for a written price, or read more on our Dryer Vent Cleaning service page.
Dryer Vent Inspection
Signs you need it
Clothes take two or more cycles to dry, the dryer exterior gets unusually hot, or the flap outside no longer opens fully when the dryer runs.
What it costs in Temple City
A camera-assisted inspection typically runs $95-$175 in Temple City, and we include still images from the camera feed in your written record.
How we do it
We run a high-resolution camera through the full vent run from the dryer connection to the exterior termination, marking every restriction, joint separation, or damage point.
Lint Removal
Signs you need it
Visible lint around the exterior vent opening, a dryer that trips its thermal sensor, or a burn smell during operation.
What it costs in Temple City
Full-system lint removal with negative-pressure and brush agitation typically runs $150-$300 depending on run length and access.
How we do it
We connect a negative-pressure collection system at the vent opening, then mechanically agitate the run with rotating brushes to dislodge caked lint, pulling it to an exterior containment unit.
Vent Rerouting
Signs you need it
The current vent path violates code with excessive run length, too many 90-degree elbows, or terminates into an attic or crawlspace instead of outdoors.
What it costs in Temple City
Rerouting a dryer vent in a Temple City attic typically runs $250-$600, with moisture-damaged duct replacement included in the written price.
How we do it
We map the shortest code-compliant path to an exterior wall, run new rigid galvanized or smooth-wall duct with a maximum of two elbows, and seal every joint with foil tape before testing airflow.
Bird Guard Installation
Signs you need it
You see nesting material at the vent termination, hear birds or flapping from the laundry wall, or find droppings below the exterior vent.
What it costs in Temple City
A stainless bird guard with pest-screen installation runs $75-$150 in Temple City, installed at the termination after cleaning.
How we do it
We remove any nesting material and debris, then install a corrosion-resistant guard with screen sizing that blocks birds and rodents without restricting airflow.
What Dryer Vent Cleaning Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Dryer vent inspection with camera | $95 - $175 |
| Full-system lint removal | $150 - $300 |
| Vent rerouting with new rigid duct | $250 - $600 |
Is dryer vent cleaning really necessary in Temple City?
Yes. Inland SGV heat bakes accumulated lint into a compacted layer, and the fine Santa Ana dust load means that layer builds faster than in coastal areas. Lint is a fuel source, and a clogged vent overheats the dryer while forcing particulate back into the laundry room. We photograph the before and after, so the record speaks for itself.
How do I know the vent was actually cleaned?
Your written record includes before-and-after camera stills from inside the full vent run, from dryer connection to exterior termination. The 365-Day Done Right Promise backs the work in writing, and you can verify any step against the photo record.
Duct Repair & Sealing in Temple City
Duct repair and sealing in Temple City is usually a structural job before it is an air-quality job. The retrofitted cooling systems in those late-1940s through 1960s tract homes were originally heating-only, and the ductwork was never sized for the airflow velocity of air conditioning. Decades of 140°F attic cycles have left the flex-duct connectors brittle and often partially collapsed, and every failed connection is pulling attic dust and fiberglass particles into the living-space air stream. Read the full scope and pricing on our Duct Repair & Sealing service page or call (806) 606-6902 for a written price.
Duct Sealing
Signs you need it
Rooms stay unevenly heated or cooled, the system runs long cycles, or you can see visible gray deposits around ceiling registers.
What it costs in Temple City
Duct sealing with mastic in a Temple City ranch typically runs $375-$850 depending on accessible run length and the number of joints.
How we do it
We access each accessible joint and seam, apply a fiberglass-reinforced mastic sealant that cures into a flexible, airtight bond, and then verify the seal with a pressure test.
Flex Duct Repair
Signs you need it
Your inspection report shows collapsed or kinked flex connections, or you find significant dust build-up in the mechanical room despite regular filter changes.
What it costs in Temple City
Repairing or replacing damaged flex-duct sections typically runs $250-$550 per run in Temple City, with the specific run length written into the price before work begins.
How we do it
We cut out the collapsed or torn section, install new R-6 or better flex duct to code, and seal both connections with mastic and foil tape.
Duct Insulation
Signs you need it
In summer the air coming from supplies feels warmer than the air at the air handler, or the duct exterior is sweating in the attic.
What it costs in Temple City
Adding or replacing duct insulation in a Temple City attic typically runs $300-$700 for a full accessible system.
How we do it
We wrap each accessible metal run with closed-cell insulation to the recommended R-value, then seal and butt every seam against air intrusion.
What Duct Repair & Sealing Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Duct sealing with mastic | $375 - $850 |
| Flex duct repair or replacement | $250 - $550 per run |
| Duct insulation (full accessible system) | $300 - $700 |
Why are some Temple City duct repair quotes so much cheaper?
They are often quoting a per-vent price that does not include the failed connectors and mastic work the job actually needs. One flat written price per system, agreed before work starts, means no add-on surprises after the van arrives.
How do I know the seal actually fixed the leak?
Your photo record shows the sealing work at every accessible joint. We also run a pressure test where the system configuration allows it, and the reading is documented in your written record.
Air Quality & Sanitizing in Temple City
Air quality and sanitizing in Temple City has to answer the two things this city’s location throws at a home: wildfire smoke residue from Angeles National Forest and the fine particulate load that mountain-range geography traps against the foothills. The 2009 Station Fire corridor showed how quickly a smoke event coats duct interiors and how long that residue lingers without treatment. After mechanical cleaning, we sanitize with EPA-registered products applied through the ductwork, and we document everything. Full details are on the Air Quality & Sanitizing service page.
Mold Treatment
Signs you need it
Musty odor that intensifies when the HVAC runs, visible microbial growth on registers or in the plenum, or a history of attic moisture intrusion.
What it costs in Temple City
Mold treatment on a typical Temple City ranch duct system runs $450-$1,150 depending on affected area and the treatment method.
How we do it
We identify the active growth, clean the affected surfaces mechanically, then apply an EPA-registered antimicrobial product through the duct runs with a fogger.
Odor Removal
Signs you need it
Cooking, smoke, or pet odors that return within hours of airing out the home, or a general stale smell that no amount of opening windows resolves.
What it costs in Temple City
Whole-system odor removal typically runs $250-$500 in Temple City, often combined with the cleaning service that precedes it.
How we do it
After mechanical extraction removes odor-bearing particulate, we apply an odor-neutralizing treatment through the plenum and each supply run, then let the system cure before testing airflow.
UV Light Installation
Signs you need it
Recurring microbial growth after cleaning, family members with persistent allergy symptoms indoors, or visible growth on the evaporator coil.
What it costs in Temple City
UV light installation at the evaporator coil typically runs $350-$800 in Temple City including the lamp and installation.
How we do it
We mount the UV lamp in the supply plenum where it shines directly on the coil and drain pan, killing microbial growth continuously while the system cycles.
What Air Quality & Sanitizing Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Mold treatment per system | $450 - $1,150 |
| Whole-system odor removal | $250 - $500 |
| UV light installation at coil | $350 - $800 |
Do I need sanitizing after wildfire smoke events near Temple City?
Wildfire smoke particles are fine enough to penetrate deep into ductwork and linger for months. Sanitizing after extraction neutralizes the odor-bearing and microbial residue that mechanical cleaning alone removes but does not treat. Your photo record shows the before and after.
Are the sanitizing products safe around my family?
We use EPA-registered products applied per manufacturer specifications, with the system off during application and adequate curing time before the blower is restarted. The product names are written into your job record, and you can verify them independently.
Brands We Service in Temple City
Temple City homes carry a mix of original and retrofit HVAC equipment, and our technicians work on all of it. The most common brands we service include Carrier, Rheem, Trane, Lennox, Goodman, York, and American Standard. Common replacement parts are stocked on our service vehicles, and we maintain a full our brands reference page so you can verify compatibility before we arrive.
Pricing for Air Duct Cleaning in Temple City, CA
| Service | Typical range in Temple City |
|---|---|
| Dryer vent inspection with camera | $95 - $175 |
| Full-system dryer lint removal | $150 - $300 |
| Dryer vent rerouting | $250 - $600 |
| Bird guard installation | $75 - $150 |
| Duct sealing with mastic | $375 - $850 |
| Flex duct repair / replacement | $250 - $550 per run |
| Duct insulation | $300 - $700 |
| Mold treatment | $450 - $1,150 |
| Odor removal | $250 - $500 |
| UV light installation | $350 - $800 |
In Temple City two factors push pricing upward: attic access in original ranch homes with low-slope roofs and tight corners adds labor time, and brittle 1960s flex connectors often need replacement during a cleaning job. Every price above is written and agreed before a single panel comes off, under Haven Standard Clause 1.
Neighborhoods We Serve in Temple City
Temple City’s original tract neighborhoods and the later infill development both present different ducted-system conditions, and our crews work them all with the same written-price standard. Typical response time for a Temple City call is 1-2 business days for scheduling, with written price delivered before the scheduling is confirmed.
- The original 1950s tract north of Live Oak Avenue
- The neighborhoods south of Las Tunas Drive
- The eastern residential streets along Rosemead Boulevard
- The communities around Temple City Park
- The tract area near Longden Avenue and Baldwin Avenue
Service Area - Cities Near Temple City
Temple City borders several communities in the western San Gabriel Valley, many with the same post-war housing era and inland heat profile. We serve El Monte, CA, San Gabriel, CA, Arcadia, CA, and Rosemead, CA with the same written-price standard and documented photo record on every job.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Air Duct Cleaning in Temple City
Our Temples City scheduling runs 1-2 business days for most jobs. We coordinate from our Los Angeles dispatch office and crews work Temple City routes daily, so the written price is delivered before the appointment is confirmed.
Most Temple City residential duct cleaning and repair work requires no HOA approval or city permit because it is an interior mechanical service, not a structural change. If your home is in a community with architectural review, your written scope documents everything for the HOA file.
Yes, but we inspect first. Brittle or collapsed connectors need repair or replacement before cleaning can be effective, otherwise the negative pressure will simply pull more attic air through the failed joints. The written price covers whatever the inspection shows.
For a free estimate on any service on this page, call (806) 606-6902. Every written price is delivered before work begins, and every job ends with a documented photo record of the work.
What happens when you call
- 1A real person answersNo phone trees - talk to a local air duct cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Temple City Customers Say
"Flat price agreed up front, no per-vent add-ons at the end. That was the whole reason I did not call the coupon company."
- Suzanne B."The dryer vent was almost completely blocked with lint. They showed me the photograph and I understood immediately why the dryer had been running twice."
- Lucia M."They found a disconnected duct in the crawl space that had been dumping conditioned air under the house for years. Photographed it, quoted the repair, fixed it."
- Devon A.