Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAir Duct Cleaning in Madera, CA
Dryer vent cleaning in Madera is not a quick luxury service here. It is a necessary response to a valley climate that pushes 100°F air through ventilation systems for months, combined with housing stock built tight and fast during the 1990s and 2000s surge. A clogged dryer vent in Madera forces the appliance to run longer cycles against restricted airflow, which raises temperatures inside the vent pipe and turns accumulated lint into a fire hazard. Call Tomas Reyes at CleanRun Air Duct Cleaning at (806) 606-6902, and we will name a written price before any work begins.
Why Madera Homes Are Different
Madera sits in the geographic center of Madera County, surrounded by active almond orchards, vineyards, and dairy operations. That location matters for ductwork. During fall harvest, almond shaking and grape picking send fine agricultural dust across the county in visible clouds, and residential HVAC systems pull that dust directly into return registers. Madera neighborhoods like Parksdale, Westgate, and the older grid near downtown all face the same seasonal spike, but the housing stock responds differently depending on age.
Homes built in the 1990s and 2000s, concentrated in newer tracts along Cleveland Avenue and north of the Madera Fairgrounds, typically use flex duct routed through attics that reach 150°F in July and August. That heat softens the flex duct outer jacket, causing sagging at mid-span and separation at the takeoff collars. Once separated, the negative pressure inside the duct pulls attic insulation, rodent droppings, and blown dust directly into the air stream. Older homes near downtown Madera, built in the 1960s and 1970s, have sheet-metal duct runs that have not been cleaned in years and show a hardened grease-and-dust bonding from repeated valley particulate cycles. The San Joaquin Valley’s topographic bowl also traps PM2.5 and wildfire smoke, including smoke from the 2020 Creek Fire that burned within Madera County. Duct systems in Madera are filtering some of the most polluted air in the nation, which is why a visual inspection of the interior of each run matters more here than in coastal cities.
Our Main Madera Services
Two services account for most of the calls we take from Madera homeowners: full air duct cleaning and complete HVAC system cleaning. Each addresses the agricultural dust, attic heat, and particulate cycling that define this part of Madera County.
Air Duct Cleaning in Madera
Full air duct cleaning in Madera means removing the layered debris that valley air deposits inside duct runs: field dust, harvest chaff, dairy particulates, and smoke residue. We photograph every run before and after, so a homeowner sees exactly what was removed. The work typically covers supply and return ducts, the supply plenum, the return air drop, and each register. For details on what a complete job includes and what Madera homeowners should expect to pay, see Air Duct Cleaning in Madera.
HVAC Cleaning in Madera
HVAC cleaning in Madera goes beyond the duct runs to the equipment that moves air. That includes the evaporator coil, the blower wheel and housing, the condensate drain pan, and the air handler cabinet. In Madera, these components collect the same agricultural film that coats the ducts, reducing airflow and cooling capacity during the long summer run. A documented photo record of the coil before and after is part of every job. Learn what is covered and typical pricing at HVAC Cleaning in Madera.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterDryer Vent Cleaning in Madera
Dryer vent cleaning in Madera addresses a specific local problem: long vent runs in single-story tract homes built during the 1990s and 2000s, combined with continuous summer use and the extra lint load from frequent laundering during harvest season. We see vents packed with compacted lint, plastic bottles, bird nesting, and more than one dead rodent. CleanRun has performed Dryer Vent Cleaning as a core service since the company started, and every Madera job includes a documented photo record of the vent interior before and after. If a vent is clogged, the dryer runs hotter and longer, and the risk of a lint fire rises. We name the written price before any panel comes off.
Dryer Vent Inspection
Signs you need it
If clothes are taking more than one cycle to dry, the exterior vent flap does not open when the dryer runs, or the laundry room feels humid mid-cycle, schedule an inspection.
What it costs in Madera
A stand-alone dryer vent inspection in Madera ranges from $49 to $149, applied toward the cleaning if work is approved.
How we do it
We run a camera down the full vent run, photograph the blockage at every elbow and transition, and show you the image before proposing any work.
Vent Cleaning
Signs you need it
The dryer runs hot to the touch, lint accumulates around the exterior vent opening, and drying times creep past 50 minutes per load.
What it costs in Madera
Full dryer vent cleaning in Madera typically runs $110 to $260, depending on vent length and accessibility.
How we do it
We send a rotating brush through the entire vent run, use negative-pressure extraction to capture dislodged lint, then photograph the clean vent wall.
Lint Removal
Signs you need it
A sudden drop in drying efficiency right after a period of heavy laundry or after moving into a previously owned Madera home.
What it costs in Madera
Heavy lint removal and compacted blockage clearing runs $130 to $280 in Madera when the blockage requires mechanical extraction.
How we do it
We dislodge the compacted lint with a reverse-drive auger, pull it back toward the interior access point, and bag the debris for removal.
Vent Rerouting
Signs you need it
The existing vent run exceeds 25 feet, has more than two elbows, or discharges into an attic, crawlspace, or covered patio instead of outside.
What it costs in Madera
Rerouting a dryer vent in Madera costs $350 to $750, including new rigid metal duct, wall cap, and sealing at each joint.
How we do it
We cut a new exterior termination point along the shortest legal path, install rigid metal duct with mastic-sealed joints, and photograph the finished run.
Bird Guard Installation
Signs you need it
The exterior vent flap is missing or warped, nesting material is visible at the vent opening, or you hear scratching from the vent area at dusk.
What it costs in Madera
Installing a louvered bird guard with a metal screen over an existing 4-inch vent termination runs $75 to $150 in Madera.
How we do it
We mount a screened hood over the vent outlet, seal the perimeter with exterior-grade caulk, and confirm the flap opens under normal dryer pressure.
What Dryer Vent Cleaning Costs in Madera
| Item | Typical range in Madera |
|---|---|
| Stand-alone inspection | $49 - $149 |
| Full vent cleaning | $110 - $260 |
| Heavy lint removal | $130 - $280 |
How often should a dryer vent be cleaned in Madera?
Every 12 months in Madera homes where the dryer runs four or more loads per week. Agricultural dust loading during harvest season shortens the interval further, and we recommend checking the exterior vent opening every October.
Why does my dryer vent clog faster in Madera than in Fresno?
Madera County is surrounded by almond orchards and dairies, and fine agricultural dust bonds with dryer lint inside the vent pipe. That creates a denser, stickier buildup than the lint-only clogs more common in less agricultural areas. Call (806) 606-6902 for a documented inspection.
Duct Repair & Sealing in Madera
Duct repair and sealing in Madera deals directly with the way this city’s attics break down ductwork. Flex duct in 1990s and 2000s tract homes sags in 150°F attic heat, pulls loose at takeoff collars, and starts pulling attic dust into the air stream. Older sheet-metal ducts near downtown Madera leak at old tape seams and drive up cooling costs all summer. CleanRun handles Duct Repair & Sealing with a written price named before any work starts, and every repaired run is photographed before and after as part of the standard job record.
Duct Sealing
Signs you need it
Rooms furthest from the air handler stay noticeably warmer in summer, or you can feel air moving in the attic near duct joints.
What it costs in Madera
Sealing accessible duct runs with mastic and mesh tape in Madera typically runs $350 to $700 per system.
How we do it
We locate every leak point, apply mastic and mesh over the separation, and photograph each sealed joint before moving to the next.
Flex Duct Repair
Signs you need it
Flex duct in a Madera attic has visibly collapsed, disconnected at a takeoff collar, or shows rodent damage at the vapor barrier.
What it costs in Madera
Replacing a damaged flex duct run in Madera runs $180 to $380 per run, depending on diameter and run length.
How we do it
We cut out the failed section, install new insulated flex duct with code-rated support strapping, and seal both ends with mastic.
Metal Duct Repair
Signs you need it
Older sheet-metal duct near central Madera has separated at longitudinal seams, rusted through at the bottom, or crushed sections under insulation.
What it costs in Madera
Patching and resealing sheet-metal duct runs in Madera runs $250 to $550 depending on access and the number of failed seams.
How we do it
We close separated seams with mechanical fasteners and mastic, patch through-corrosion with new sheet metal, and photograph the completed repairs.
Duct Insulation
Signs you need it
Ductwork sweats during winter Tule fog events, causing water stains on ceiling drywall near registers in Madera homes.
What it costs in Madera
Insulating or reinsulating accessible attic ductwork in Madera runs $400 to $900 for a typical single-story home.
How we do it
We wrap the duct runs with new R-6 or R-8 insulation, seal the jacket seams, and photograph the finished insulation at representative points.
What Duct Repair & Sealing Costs in Madera
| Item | Typical range in Madera |
|---|---|
| Accessible duct sealing | $350 - $700 |
| Flex duct run replacement | $180 - $380 per run |
| Sheet-metal patch and reseal | $250 - $550 |
Can you seal ducts without tearing out walls in Madera?
Yes, in most single-story Madera homes the duct work is accessible from the attic. We seal every accessible joint with mastic and only cut into drywall if there is no other way to reach a failed run.
Why does my flex duct keep sagging apart in the Madera summer?
Attic heat exceeding 150°F softens the plastic liner on flex duct, causing it to stretch and pull loose at takeoff collars. Proper support strapping at code intervals prevents this, and we install it on every new run. Call (806) 606-6902 for a written scope.
Air Quality & Sanitizing in Madera
Air quality and sanitizing in Madera responds to the valley’s relentless particulate load and the mold risk from winter Tule fog condensation. Almond orchard dust, dairy particulates, and wildfire smoke settle inside ductwork, and once organic debris gets damp, mold colonization follows quickly. CleanRun applies Air Quality & Sanitizing only after the ductwork is clean, and every sanitizing job in Madera includes before and after photos of the treated surfaces.
Mold Treatment
Signs you need it
Musty odor comes from registers when the system starts, or black staining is visible inside a duct run during a camera inspection.
What it costs in Madera
Mold treatment of accessible ductwork in Madera runs $450 to $900 depending on linear feet treated and severity.
How we do it
We apply an EPA-registered antimicrobial to affected surfaces, allow the required dwell time, and photograph the treated area dry.
Bacteria Sanitizing
Signs you need it
A household member has recurring sinus issues indoors, or a property transfer requires documentation of sanitized ductwork in Madera.
What it costs in Madera
Whole-system bacteria sanitizing in Madera runs $250 to $500 when combined with a full duct cleaning.
How we do it
We fog an EPA-registered sanitizer through the duct system under negative pressure, dwell, and ventilate before the system is returned to service.
Odor Removal
Signs you need it
Persistent cooking, pet, or smoke odor returns within days of cleaning surfaces and replacing filters in a Madera home.
What it costs in Madera
Odor removal treatment in Madera runs $300 to $600 and is applied after the source debris has been mechanically removed.
How we do it
We locate the odor source photographically, remove the contaminated material, and treat remaining surfaces with an odor-neutralizing agent.
UV Light Installation
Signs you need it
Recurring coil mold despite professional cleaning, or a household member with a diagnosed respiratory condition in a Madera home.
What it costs in Madera
UV lamp installation on an existing air handler in Madera runs $550 to $950, including the lamp hardwired with a dedicated switch.
How we do it
We mount a Honeywell UV lamp in the supply plenum above the evaporator coil, hardwire it with a sight-glass indicator, and photograph the install.
What Air Quality & Sanitizing Costs in Madera
| Item | Typical range in Madera |
|---|---|
| Mold treatment of ductwork | $450 - $900 |
| Bacteria sanitizing with duct cleaning | $250 - $500 |
| UV light installation | $550 - $950 |
Is sanitizing the same thing as cleaning in Madera?
No. Cleaning removes the physical debris. Sanitizing treats the surfaces after the debris is gone. We do not sell sanitizing as a substitute for cleaning, and Madera attics make the sequence matter because organic dust supports mold growth.
Do you apply sanitizer before or after duct cleaning?
After. Applying a sanitizer over accumulated agricultural dust and lint is wasted work. The surface must be clean or the treatment cannot reach it. Call (806) 606-6902 for a written price on the full sequence.
Brands We Service in Madera
Our Madera crews work on equipment from Guardsman, Rotobrush, Nikro, and Honeywell. Common replacement parts, including UV lamps and access panel gaskets, are stocked in the Fresno Central Valley office and arrive in Madera the same week. See our brands for the full equipment roster.
Pricing for Air Duct Cleaning in Madera, CA
| Service | Typical range in Madera |
|---|---|
| Stand-alone dryer vent inspection | $49 - $149 |
| Full dryer vent cleaning | $110 - $260 |
| Heavy lint removal | $130 - $280 |
| Dryer vent rerouting | $350 - $750 |
| Bird guard installation | $75 - $150 |
| Duct sealing (accessible system) | $350 - $700 |
| Flex duct run replacement | $180 - $380 per run |
| Metal duct patch and reseal | $250 - $550 |
| Duct insulation | $400 - $900 |
| Mold treatment of ductwork | $450 - $900 |
| Bacteria sanitizing with duct cleaning | $250 - $500 |
| UV light installation | $550 - $950 |
Prices in Madera push toward the upper end when attics are tight, duct runs are long, or the existing work requires correcting a previous company’s poor installation. Every job starts with a written price under Haven Standard Clause 1, and that number does not change after the truck arrives.
Neighborhoods We Serve in Madera
CleanRun serves single-family homes across Madera, from the older grid near downtown to the newer tracts north and east of the fairgrounds. Response time from the Fresno Central Valley office is typically same-week scheduling for most Madera neighborhoods.
- Parksdale
- Westgate
- Downtown Madera
- Madera Ranchos
- Bonadelle Ranchos
Service Area - Cities Near Madera
Our crews also work in Fresno, CA and Clovis, CA, where agricultural dust loads differ but the same valley particulate problem holds. To the south, Sanger, CA and Selma, CA see similar orchard dust and Tule fog conditions. Scheduling is coordinated from the Fresno Central Valley office for all Madera jobs.
Serving Madera, CA - Our Local Coverage Area
We’re based in the Madera area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Air Duct Cleaning in Madera
No permit is required in Madera for cleaning or sealing existing ductwork, dryer vent cleaning, or sanitizing. Adding new vent termination through an exterior wall may require code compliance, which we confirm at the written scope stage. We do not pull permits for standard cleaning jobs.
During fall almond and grape harvests, fine agricultural dust spikes filter loading. In Madera, a 1-inch pleated filter can clog in under two weeks during harvest season. Schedule a post-harvest duct inspection every October and check the filter monthly through November. Call (806) 606-6902 to schedule.
Yes. The inside of every duct run we work on is photographed before we start and after we finish. That photo record is delivered to you as part of the standard job documentation, not as an add-on. You can verify what was actually removed.
What happens when you call
- 1A real person answersNo phone trees - talk to a local air duct cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Madera Customers Say
"They found a disconnected duct in the crawl space that had been dumping conditioned air under the house for years. Photographed it, quoted the repair, fixed it."
- Devon A."On time, professional, and explained what the readings meant without talking down to me."
- Warren E."The before and after photographs of each run are the reason I used them. You cannot argue with what came out of the return."
- Marguerite O.